Properties and application scope of the No.20 steel
This is a quality low-carbon steel and a cold extruded, carburized and quenched steel, featuring low strength, high toughness, high plasticity and high weldability, with a tensile strength of 253-500MPa and a elongation ≥24%. Except carbon (C) and a certain amount of silicon (Si) (normally less than 0.40%) and manganese (Mn) (normally less than 0.80% and sometimes up to 1.20%) for deoxygenation, no other alloying elements contained (residual elements excluded). It is called wrought iron when the content of carbon is less than 0.02%, pig iron when the content of carbon is bigger than 2.11% and less than 4.3%, and steel when when the content of carbon is in between.
Purposes of the No.20 steel
This steel is applicable to manufacturing automobiles, tractors or small and medium-sized carburized and carbonitrided parts which are not very important in the general machinery manufacturing, such as the hand brake shoes, lever shafts, gearbox forks, transmission and ring gears on automobiles as well as the camshafts, suspended equalizer shafts, equalizer linings and sleeves. It is used to manufacture various mechanical parts which are not subjected to large forces and have high toughness requirements in the hot rolling or normalizing state. In the heavy and medium machinery manufacturing industry, it is used to manufacture forged or pressed pull rods, shackles, levers, sleeves and fixtures. In the turbine and boiler industry, it is mostly used for the pipes, flanges, headers and various fasteners that operate in non-corruptive media with pressure ≤6N/mm2 and temperature ≤450℃. It is also used to manufacture castings such as crossheads and pistons for railways and the rolling stock.
Purposes of the guide shaft carbon steel components
The chrome plated bar or cold drawn bar is normally used to perform surface oxidation treatment for the guide shaft. With the main function of guiding, the guide shaft is used together with different components for different purposes. The guide shaft serves the purposes of rectilinear motion, rotation and being used as a pillar.
Usually used together with different components, the carbon steel guide shaft component serves different purposes: in rectilinear motion, it is used together with a linear bearing, a guide shaft stool and an oil-free bush. A linear guide shaft can be used with a linear bearing to form a rectilinear motion mechanism. When used together with a linear bearing, a thermally treated carbon steel guide shaft component with an allowance of ｇ6·ｈ8·ｈ5 can be selected. When used together with an oil-free bush, a guide shaft component which is not thermally treated and has an allowance of f8 can be selected. For the purpose of revolution, the guide shaft is normally used together with a bearing, synchronous pulleys and couplings. When the guide shaft is used as a pillar, normally pillar attaching clips, a pedestal and a fixing ring are used together with it.
The main purposes of the linear guide shaft
1.Light-load, short-distance, low-frequency and low-speed motion in the vertical direction.
2.High-speed, long-distance, heavy-load and high-frequency motion in the horizontal direction.
3.Used together with an oil-free bush, a guide shaft component which is not thermally treated and has an allowance of f8 can be hard chrome plated on its surface for surface contact sliding.
As far as only the appearances are concerned, the guide shafts manufactured by different CNC machining parts suppliers may be quite similar. However, a guide shaft’s performances are mostly affected by the standards and manufacturing processes selected by the CNC machining parts supplier during production.
CNC machining is an important manufacturing process where pre-programmed computer software is used. It dictates the various movements of machinery and factory tools. The process is integral to the efficient working of any factory because it helps in controlling the functioning and movement of a range of complex machineries. These could range from lathes to grinders and also routers. When you use the right CNC machining parts it is possible to perform complicated three dimensional cutting jobs. This can be done using a single set of commands and prompts. CNC actually stands for computer numerical control and this takes into account the limitations that exist as far as manual control is concerned.
In order to pursue the high quality requirements of many industries around the world, Yjin has purchased the best German CNC milling machines, Swiss CNC lathes, German screw machines and Japanese high-precision testing equipment on the market. We have CNC 3 axis, 4 Axis, 5 axis, high-speed 30T stamping equipment, die-casting equipment, high-precision screw machine, cold heading machine, and we are constantly pursuing technological breakthroughs and training talents. When you need high-quality product accuracy and complete processing services, Yjin Hardware can help you with design concepts, product development, mass production and other hardware components expertise and professional processing cooperation. Call us or email us today, we Can immediately provide you with 24-hour professional services and professional processing cooperation.
With the efforts of all of Yijin’s colleagues, the company continues to develop steadily, and maintains long-term good relations of cooperation with global aerospace, military, medical, and communications companies. Product quality and accuracy have been appreciated and praised by all customers.